expertfea.com logo

Solved FEA Pack 14 (Cases 131-140)


If you are interested in running the FEA scenarios seen underneath, you can download their MECHDAT files to see the settings we used for materials, mesh, contacts, loads, time steps, solver etc., together with their 3D models. On this page you find only MECHDAT files and 3D models; the PDF tutorials are found on the pages seen in the menu!

ANSYS WB 17.1 OR HIGHER

131. 1st in the World!!! - ANSYS WB FEA - Heat generation and dissipation in a disk brake (trial)

Click for video with results on

Not recommended to beginners! If you have at least ANSYS WB 17.1, get the MECHDAT file + 3D model for 19$

ANSYS WB 15 OR HIGHER

132. ANSYS WB FINITE ELEMENT ANALYSIS - 2D simulation of machining an Aluminum work-piece

Click for video with results on

If you have at least ANSYS WB 15, get the MECHDAT file + 2D model for 13$

ANSYS WB 15 OR HIGHER

133. 1st in the World!!! ANSYS WB FEA - Single Point Incremental Sheet Forming Simulation

Click for video with results on

If you have at least ANSYS WB 15, get the MECHDAT file + 3D model for 14$

ANSYS WB 15 OR HIGHER

134. 1st in the World!!! ANSYS WB FEA - Rubber part falling on conveyor due to gravity

Click for video with results on

If you have at least ANSYS WB 15, get the MECHDAT file + 3D model for 13$

ANSYS WB 15 OR HIGHER

135. 1st in the World!!! ANSYS WB EXPLICIT DYNAMICS WITH FLUIDS - Water paddling in kayak-canoe (trial)

Click for video with results on

If you have at least ANSYS WB 15, get the MECHDAT file + 3D model for 13$

ANSYS WB 15 OR HIGHER

136. 1st in the World!!! ANSYS WB EXPLICIT DYNAMICS - Popping/ bursting a balloon with a pin/ tack

Click for video with results on

If you have at least ANSYS WB 15, get the MECHDAT file + 3D model for 12$

ANSYS WB 15 OR HIGHER

137. 1st in the World!!! ANSYS WB EXPLICIT DYNAMICS WITH FLUIDS - Air spring compressed 1 bar vs. 100 bar

Click for video with results on

If you have at least ANSYS WB 15, get the MECHDAT file + 3D model for 15$

ANSYS WB 15 OR HIGHER

138. 1st in the World!!! ANSYS WB EXPLICIT DYNAMICS WITH FLUIDS - Dummy without seatbelt impacting airbag

Click for video with results on

If you have at least ANSYS WB 15, get the MECHDAT file + 3D model for 14$

ANSYS WB 15 OR HIGHER

1st in the World!!! ANSYS WORKBENCH FEA - 3 stage thinning of a Copper slab via cold roll forming

Click for video with results on

If you have at least ANSYS WB 15, get the MECHDAT file + 3D model for 15$

☆ The MECHDAT files give you hints for your FEA work or training, by observing our set-up: geometry, materials, mesh, boundary conditions, analysis settings and solution items as seen in their Youtube clips. Solving is not guaranteed 100%, because ANSYS continuously changes the solving algorithms; usually they do a good job, sometimes...

☆ After you made the purchase, open the MECHDAT file and re-solve the FEA as follows:

⇒ for Static and Transient Structural: right click Solution, Clear Generated Data, Solve;

⇒ for Explicit Dynamics: right click Solution, Clear Generated Data, then go to Analysis Settings, Step Controls, Resume From Cycle = 0, Solve.

☆ Pay attention to the mentioned ANSYS Workbench version, because older versions will not open the files!