Solved FEA Pack 8 (Cases 71-80)

Get these FEA files to see the settings we used for materials, mesh, contacts, loads, time steps, solver etc. On this page you find only MECHDAT or WBPZ files and 3D models, while the PDF tutorials are found on the TUTORIALS and SHORT TUTORIALS pages!

ANSYS WB 15 OR HIGHER

71. BEST IN THE WORLD ANSYS Workbench Static Structural FEA of a full ball bearing under load

Click for video with results on

Get the ANSYS Workbench data as MECHDAT file + the 3D model for only $16

ANSYS WB 15 OR HIGHER

72. ANSYS Workbench Explicit Dynamics FEA of helicopter crashing into a pole (trial 2)

Click for video with results on

Get the ANSYS Workbench data as MECHDAT file + the 3D model for only $15

ANSYS WB 15 OR HIGHER

73. ANSYS Workbench Explicit Dynamics FEA of a rubber part falling on metal pins

Click for video with results on

Get the ANSYS Workbench data as MECHDAT file + the 3D model for only $15

ANSYS WB 15 OR HIGHER

74. ANSYS Workbench Static Structural FEA of a small car on a 1° inclined road (trial)

Click for video with results on

Get the ANSYS Workbench data as MECHDAT file + the 3D model for only $16

ANSYS WB 15 OR HIGHER

75. ANSYS Workbench Transient Structural FEA of a filled tire pressing on a rotating drum

Click for video with results on

Get the ANSYS Workbench data as MECHDAT file + the 3D model for only $16

ANSYS WB 15 OR HIGHER

76. ANSYS Workbench Explicit Dynamics FEA of bullet penetrating through a bucket (optimized)

Click for video with results on

Get the ANSYS Workbench data as MECHDAT file + the 3D model for only $15

ANSYS WB 15 OR HIGHER

77. ANSYS Workbench Explicit Dynamics FEA of Charpy V-notch impact test

Click for video with results on

Get the ANSYS Workbench data as MECHDAT file + the 3D model for only $14

ANSYS WB 15 OR HIGHER

78. ANSYS Workbench Explicit Dynamics FEA of a knife cutting a jelly part

Click for video with results on

Get the ANSYS Workbench data as MECHDAT file + the 3D model for only $15

ANSYS WB 15 OR HIGHER

79. ANSYS Workbench Transient Structural FEA of a chain on a sprocket

Click for video with results on

Get the ANSYS Workbench data as MECHDAT file + the 3D model for only $16

ANSYS WB 15 OR HIGHER

80. ANSYS Workbench Explicit Dynamics FEA simulations of a rubber cloth

Click for video with results on

Get the ANSYS Workbench data as MECHDAT file + the 3D model for only $15

☆ The MECHDAT files give you hints for your FEA work or training, by observing our set-up: geometry, materials, mesh, boundary conditions, analysis settings and solution items as seen in their YouTube clips. Solving is not guaranteed 100%, because ANSYS continuously changes the solving algorithms; usually they do a good job, sometimes...

☆ After you made the purchase, open the MECHDAT file and re-solve the FEA as follows:

⇒ for Static and Transient Structural: right click Solution, Clear Generated Data, Solve;

⇒ for Explicit Dynamics: right click Solution, Clear Generated Data, then go to Analysis Settings, Step Controls, Resume From Cycle = 0, Solve.

☆ BE SURE TO HAVE THE SAME OR EVEN A NEWER ANSYS VERSION, BECAUSE OLDER VERSIONS WILL NOT OPEN THE NEWER FILES!