Solved FEA Pack 30 (Cases 291-300)

Get these FEA files to see the settings we used for materials, mesh, contacts, loads, time steps, solver etc. On this page you find only MECHDAT or WBPZ files and 3D models, while the PDF tutorials are found on the TUTORIALS and SHORT TUTORIALS pages!

AWB 2019 R3 OR HIGHER

291. Modal, Modal Acoustics in air and Modal Acoustics of fuel pump submerged in water - ANSYS Workbench

Click for video with results on

If you have ANSYS WB 2019 R3 or higher, get the 3 ANSYS Workbench solved scenarios + the 3D model for only $17

ANSYS 19.1 OR HIGHER

292. Biomechanics simulation of the balloon valvuloplasty procedure - ANSYS Workbench Explicit Dynamics

Click for video with results on

If you have ANSYS 19.1 or higher, get the ANSYS Workbench mechdat file + the 3D model for only $19

DISCOVERY LIVE 2021 R1

293. CFD simulation of the air flow around Santa's sleigh and reindeers - Discovery LIVE 2021 R1

Click for video with results on

If you have ANSYS Discovery LIVE 2021 R1 or higher, get the DSCO file + the 3D model for only $13

ANSYS 19.1 OR HIGHER

294. Video & FEA: Modeling and simulation of a bridge from scratch using Beam elements

Click for video with results on

If you have ANSYS 19.1 or higher, get the 5 solved ANSYS Workbench cases + the 3D models for only $17

VIDEO: If you have ANSYS Workbench 19.1 or higher, get the 3D model and watch the 40 min lesson of modeling and simulation for only $17

ANSYS 19.1 OR HIGHER

295. Drop test of a glass cup with water impacting a rigid tray - ANSYS Explicit Dynamics with Fluids

Click for video with results on

If you have ANSYS 19.1 or higher, get the ANSYS Workbench mechdat file + the 3D model for only $16

ANSYS 2019 R3 OR HIGHER

296. Internal detonation of submarine shell body before submerging - ANSYS Explicit Dynamics with Fluids (v1)

Click for video with results on

If you have ANSYS 2019 R3 or higher, get the ANSYS Workbench mechdat file + the 3D model for only $17

ANSYS 2020 R2 OR HIGHER

297. 3 stage rolling with plasticity through eccentric rollers - ANSYS Workbench Static Structural

Click for video with results on

If you have ANSYS 2020 R2 or higher, get the ANSYS Workbench WBPZ archive + the 3D model for only $17

ANSYS 2021 R1 OR HIGHER

298. 4 Point Bending of an Unreinforced Concrete Beam - ANSYS Workbench Explicit Dynamics with SPH

Click for video with results on

If you have ANSYS 2021 R1 or higher, get the ANSYS Workbench WBPZ archive + the 3D model for only $16

ANSYS 2021 R1 OR HIGHER

299. Simulation of biting with full separate teeth and solid jaw (v1) - ANSYS Workbench Explicit Dynamics

Click for video with results on

If you have ANSYS 2021 R1 or higher, get the ANSYS Workbench WBPZ archive + the 3D model for only $17

ANSYS 2021 R1 OR HIGHER

300. Coupled Field Static simulation of heat generated between pin and disk, v1 - ANSYS Workbench 2021 R1

Click for video with results on

If you have ANSYS 2021 R1 or higher, get the ANSYS Workbench WBPZ archive + the 3D model for only $16

No APDL commands are needed, only simple mechanical loads are used!!!

☆ The MECHDAT files give you hints for your FEA work or training, by observing our set-up: geometry, materials, mesh, boundary conditions, analysis settings and solution items as seen in their YouTube clips. Solving is not guaranteed 100%, because ANSYS continuously changes the solving algorithms; usually they do a good job, sometimes...

☆ After you made the purchase, open the MECHDAT file and re-solve the FEA as follows:

⇒ for Static and Transient Structural: right click Solution, Clear Generated Data, Solve;

⇒ for Explicit Dynamics: right click Solution, Clear Generated Data, then go to Analysis Settings, Step Controls, Resume From Cycle = 0, Solve.

☆ BE SURE TO HAVE THE SAME OR EVEN A NEWER ANSYS VERSION, BECAUSE OLDER VERSIONS WILL NOT OPEN THE NEWER FILES!